Skip to content

Straight talk about your car's repair, like a neighbor

(559) 468-3243
(559) 468-3243

ServicesFrame Straightening

Frame Straightening in Kerman

A hard hit can shift the structure under your car even when the outside looks fine. We measure your vehicle against the maker's dimensions, pull the frame or unibody back where it belongs, and show you the before and after readings so you know it is right.

Technician seen from behind attaching a pulling chain to a damaged gray sedan clamped on a red frame-straightening machine inside a body shop bay

When the damage goes deeper than the panels

Most cars today are built on a unibody, where the floor, rails and pillars work together as the frame. Many trucks still ride on a separate ladder frame. Either way, a collision can push a rail, kink a strut tower or twist the structure a few millimeters out of line. That small shift is enough to throw off the alignment, the door gaps and how crash energy travels through the car in the next impact.

Frame straightening puts that structure back to factory dimensions. We treat your car the way we would treat a neighbor's: measure first, explain what we found in plain words, and only pull or replace what the numbers say needs it. If a section is too damaged to straighten safely, we tell you that too.

What frame straightening includes

Electronic measuring

We check dozens of reference points on the underbody and compare them to the manufacturer's published dimensions. You get a printout or photos showing where the structure sits before we touch it.

Anchoring and controlled pulls

Your vehicle is clamped to a frame machine at its pinch welds or frame mounts. We then use pull towers and chains to move the damaged area back in small, measured steps, rechecking as we go.

Sectioning or replacing parts

Some steel and most high-strength parts are not meant to be straightened past a certain point. When the repair procedure calls for it, we cut out the damaged section and weld in a new one following the maker's instructions.

Final measurement and alignment check

After the pulls, we measure again to confirm the structure is back in spec. We then check wheel alignment and suspension mounting points so your car drives straight.

Coordination with the rest of the repair

Frame work is usually one part of a larger job. Our collision repair and paint and refinishing work follow once the structure is true, so new panels line up and gaps stay even.

Signs your car may need frame straightening

  • It pulls or the wheel sits crooked

    If your car drifts to one side or the steering wheel is off center after an accident, the cause may be more than alignment. A shifted rail or suspension mount can do the same thing.

  • Doors, hood or trunk don't line up

    Uneven gaps or a door that suddenly needs a slam to close often point to a structure that has moved.

  • Tires wearing unevenly

    Fast wear on one edge of a tire, even after an alignment, can mean the mounting points themselves are out of place.

  • Wrinkles underneath or in the trunk floor

    Creases in the floor pan, trunk floor or inner fender show where crash force traveled. They are worth having measured.

  • Odd noises over bumps

    New creaks, rattles or clunks after a collision can come from parts that no longer sit where they should.

How a frame repair works at our shop

  1. 1

    Look it over and measure

    You bring your car in and we inspect the damage, then put it on the measuring system. We walk you through what the readings show before any work starts.

  2. 2

    Write up the estimate

    You get a written estimate that lists the pulls, any parts to be replaced and the related body and paint work. If there is an insurance claim, we send the same details to your adjuster.

  3. 3

    Straighten and repair

    We anchor the vehicle, make the pulls and replace sections where the procedure requires it. Measurements are taken throughout, not just at the end.

  4. 4

    Verify and finish

    Once the structure is back in spec, we finish the panels, paint and alignment. We go over the final readings with you when you pick up your car.

What affects the cost of frame straightening

There is no single price for frame work because no two collisions bend a car the same way. We price it after measuring, and the estimate shows each step so nothing comes as a surprise.

How far the structure moved
A rail pushed a few millimeters takes far less time on the machine than a corner that was crushed and twisted.
Unibody or full frame
Unibody cars often need more anchoring and more points corrected at once. Trucks with separate frames can sometimes be repaired in one area.
Parts that must be replaced
High-strength steel, aluminum and some crush zones are replaced rather than pulled. New sections and the welding time add to the job.
Related repairs
Most frame jobs also include panels, bumper repair, paint and a wheel alignment. Those are listed separately on the estimate.

Frame straightening questions

Something not covered here? (559) 468-3243

Can a bent frame really be fixed safely?

In many cases, yes. When the structure is measured, pulled within the maker's limits and verified afterward, it can perform the way it was designed to. Where a part is past its limits, we replace it instead of forcing it straight.

Does frame damage mean my car is totaled?

Not necessarily. Whether a car is totaled depends on the repair cost compared with its value, and that is your insurer's call. Plenty of cars with frame damage are repaired and back on the road.

How long will my car be in the shop?

It depends on how much the structure moved, which parts need ordering and how much body and paint work follows. We give you a realistic timeline once the car is measured and keep you posted if anything changes.

Will my insurance cover frame straightening?

If the damage came from a covered accident, frame work is usually part of the claim. We send the adjuster our measurements and estimate, and our insurance claims page explains how we help with the paperwork.

Will the car drive the same afterward?

That is the goal of every frame job. Once the structure is back in spec, we check the alignment so your car tracks straight, and we'll tell you if anything else still needs attention.

Gray SUV parked on a wet concrete lot outside a metal body shop, with open bays, a masked car ready for paint, and a front-damaged car nearby

Worried your frame took a hit?

Tell us what happened and how your car is driving. We'll explain what to look for and set a time for you to bring it in for measuring.